Turnstone Crank Quick Start Manual

Text of Turnstone Crank Quick Start Manual

Page 1 of 30

939501205 Rev A Crank Adjustable Units� Please identify the unit before selecting what section to follow� for assembly of product. R © 2002 Steelcase Inc. Grand Rapids, MI 49501 U.S.A. Printed in U.S.A. Extension Link Units with Standard Corner Units Bilevel Corner Unit Straight and Corner Units Right� Extension Left� Extension Extension Link Units with Bilevel Corner Units Section A� (begins on page 2) Section B� (begins on page

Page 2 of 30

939501205 Rev A Crank Handle� (Qty. 1) Short Mounting� Screw� (Qty. 8) Worksurface� Screw� (Qty. 6) Foot Bolt� (Qty. 4) Section A: Assembly instructions to assemble the following units:� � 45mm 5mm

Page 3 of 30

939501205 Rev A Front 1. Flip the base upside down and without� cutting the tie wraps, put the feet on. FOOT BOLTS

Page 4 of 30

939501205 Rev A Straight Standard Corner Standard 2. Install grommet (black) into laminated� side of worksurface.� � 3. Install guide (white) into grommet. 4. Cut the tie wraps.� � 5. (Optional for STANDARD� units only) Install the "nut", "washer"� and "disk" to the gas cylinder (if not� already installed). Place gas cylinder� as shown.� � NOTE: DO NOT attempt to screw or� compress the gas cylinder in

Page 5 of 30

939501205 Rev A Worksurface Screws Standard Corner Standard Straight Rear Front Rear Front 6. Place the worksurface on a protected� surface. Attach mounting plates on� worksurface, at the screw locations shown,� after aligning the pilot holes.

Page 6 of 30

939501205 Rev A Corner Standard Short Mounting Screws Straight Standard 7 10 11 8 NOTE: If unit is placed with a gas cylinder, adjust the unit to full height of travel using crank handle.� � 7. Flip base upside down on a protected surface.� � NOTE: If base has gas cylinder, be careful when inverting the base.� � 8. Mount top to base with short mounting screws.� � 9. Flip unit to upright.� � 10. Remove Guides, retain f

Page 7 of 30

939501205 Rev A Crank Handle� (Qty. 1) Short Mounting� Screw� (Qty. 8) Worksurface� Screw� (Qty. 16) Foot Bolt� (Qty. 4) Section B: Assembly instructions to assemble the following units:� � 5mm 45mm

Page 8 of 30

939501205 Rev A Front 1. Flip the base upside down and without� cutting the tie wraps, put the feet on. FOOT BOLTS

Page 9 of 30

939501205 Rev A Corner Bilevel 2. Install grommet (black) into laminated� side of worksurface.� � 3. Install guide (white) into grommet. 4. Place the worksurface on a protected� surface. Attach mounting plates on� worksurface. 2 3 Worksurface� Screws Bilevel Corner Rear Front

Page 10 of 30

939501205 Rev A 6 9 10 7 5. Cut tie wraps.� � 6. Flip base upside down on a protected surface.� � 7. Mount top to base with short mounting screws.� � 8. Flip unit to upright.� � 9. Remove Guides, retain for future assembly.� � 10. Test: Using the crank handle, adjust both the front and the rear surfaces of the unit to different heights to ensure unit works properly.� � Optional - if shrouds (ordered separately) a

Turnstone Indoor Furnishing Owners Instructions: