Philips BDL5545ET/00 Operation & User’s Manual

1 SAFETY INSTRUCTIONS WARNINGS AND PRECAUTIONS KNOW THESE SAFETY SYMBOLS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product. This symbol alerts you that important literature concerning operation and maintenance has been included with this product. Note to CATV system installer: This reminder is provided to call CATV system installer’s attention to Article 820-40 of the National Electrical ...

2 Read and follow these instructions when connecting and using your display:  Unplug the display if you are not going to use it for an extensive period of time.  Unplug the display if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry cloth when the power is off. However, never use alcohol, solvents or ammonia-based liquids.  Consult a service technician if the display does not operate normally when you have followed the instructions in this manual.  The casing cover should be opened only by qualified service personnel.  Keep the display out of direct sunlight and away from stoves or any othe ...

3 REGULATORY INFORMATION CE DECLARATION OF CONFORMITY MMD declare under our responsibility that the product is in conformity with the following standards • EN60950-1:2006+A11:2009 (Safety requirement of Information Technology Equipment) • EN55022:2006+A1:2007 (Radio Disturbance requirement of Information Technology Equipment) • EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment) • EN61000-3-2:2006 (Limits for Harmonic Current Emission) • EN61000-3-3:2008 (Limitation of Voltage Fluctuation and Flicker) following provisions of directives applicable • 2006/95/EC (Low Voltage Directive) ...

4 POLISH CENTER FOR TESTING AND CERTIFICATION NOTICE The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source. The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A). To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be located near the equipment and easily accessible ...

5 INFORMATION FOR UK ONLY WARNING - THIS APPLIANCE MUST BE EARTHED. Important: This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5A. Note: Th ...

6 NORTH EUROPE (NORDIC COUNTRIES) INFORMATION Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ. END-OF-LIFE DISPOSAL Your new display contains materials that can be recycled and ...

7 TABLE OF CONTENTS 1. UNPACKING AND INSTALLATION ................................................................................................................... 9 1.1. UNPACKING .......................................................................................................................................... 9 1.2. PACKAGE CONTENTS ......................................................................................................................... 9 1.3. INSTALLATION NOTES......................................................................................................................... 9 1.4. PORTRAIT MOUNTIN ...

8 5. INPUT MODE................................................................................................................................................... 49 6. PIXEL DEFECT POLICY ................................................................................................................................. 51 6.1. PIXELS AND SUB-PIXELS.................................................................................................................. 51 6.2. TYPES OF PIXEL DEFECTS + DOT DEFINITION............................................................................. 51 6.3. BRIGHT DOT DEFECTS ....................... ...

9 1. UNPACKING AND INSTALLATION 1.1. UNPACKING  This product is packed in a carton, together with the standard accessories.  Any other optional accessories will be packed separately.  The weight of the product differs - depending on the type. Due to the size and weight it is recommended to move it by 2 people.  After opening the carton, ensure that the contents are complete and in good condition. 1.2. PACKAGE CONTENTS Please verify that you received the following items :  Please make sure that for all other regions, apply a power cord that conforms to the AC voltage of the power socket and has been approved by and complies wi ...

10 1.4. PORTRAIT MOUNTING Wall mounting holes Notes:  Metric 8 (12mm) screws are needed for wall mounting (not included).  The mounting interface should comply with the UL1678 standard in North America. The mounting means should strong enough to bear the weight of the monitor (approx. 54.3 kg without stand). How to use the Logo Guider for Portrait Mode a. Adjust the logo guider to align the hole with the hole on the short front bezel b. Peel off the protective paper from the back side of the logo. c. Make sure that the logo is aligned with the short front bezel. Press the logo to the short front bezel firmly and repeatedly. d. R ...

11 1.5. INSTALLING AND REMOVING STAND 1.5.1 How to install stand 1. Turn off the Display. 2. After inserting the stand in the guide block, tighten the screws on both sides of the monitor. NOTE: The long end of the stand should face the front while installing. 1.5.2 How to remove the stand 1. Spread a protective sheet on a flat surface. 2. Place the display face-down on a protective sheet. 3. Remove screws using a screwdriver and place them in a safe place for reuse. Screw Stands "Longer end faces the front" Screw Screw Screw ...

12 1.5.3 Prevent display from falling To prevent the display from tipping in the event of an earthquake or other such natural event, please follow these steps. As shown in the figure below, secure the display to a solid wall or pillar using a cord which is strong enough to bear the weight of the monitor (BDL5545ET: approx. 55.8 kg). Screw hooks (ring type) are recommended. Caution:  Although the above method is recommended, it is not guaranteed that the display will not tilt over.  Before moving the display, remove the cord first. Clamper Screw Screw Holes Screw Hook, etc. ...

13 2. PARTS AND FUNCTIONS 2.1. FRONT VIEW 1. Ambient light sensor  Detects the ambient lighting condition around the display and the image brightness will automatically adjust when “LIGHT SENSOR” is set to “ON” in the OSD menu. 2. Remote control sensor  Receives command signals from the remote control unit. 3. LCD power status indicator  Indicates the operating status of the display: - Lights green when the display is turned on - Lights red when the display is in standby mode - Lights amber when the display enters DPMS mode - When SCHEDULE is enabled, the light blinks green and red - If the indicator blinks red that a ...

14 2.2. REAR VIEW 1. POWER button ( ) To switch the power on or put the display to standby. 2. MUTE button To switch the audio mute ON/OFF. 3. SOURCE button Use this button to select the input source. When the On Screen Display menu is active, this is also used as the SET button. 4. PLUS (+) button To increase the adjustment while OSD menu is on, or to increase the audio output level while the OSD menu is off. 5. MINUS (-) button To decrease the adjustment while OSD menu is on, or to decrease the audio output level while the OSD menu is off. 6. UP () button To move the highlight bar up to adjust the selected item while OSD menu i ...

15 2.3. INPUT/OUTPUT TERMINALS 1. OPS SLOT Slot for installing the optional OPS module. 2. USB For technical support (i.e. firmware upgrades) only. 3. RJ-45 LAN control function to configure your display remotely via an internet browser. For instructions on how to control the display via the LAN port, please refer to the Application Notes on the CD ROM enclosed with your display. 4. RS232C (OUT/IN) RS232C network connection input/output for the use of loop through function. 5. AUDIO IN (AUDIO1/AUDIO2/ AUDIO3) Connects to the audio output of a computer or an AV device. 6. AUDIO OUT R/L Outputs the audio signal from the AUDIO IN (AU ...

16 9. Main power switch Press to switch the main power on/off. 10. AC OUT Connects to the AC IN socket of another BDL5545ET monitor or an external media device. (Rating : 100~240Vac, 50-60Hz, 3A Max.) 11. AC IN Connects the supplied power cord to the wall outlet. 12. DISPLAY PORT Connects to the DisplayPort output of a PC or an AV device. 13. VIDEO IN (HDMI) Connects to the HDMI output of an AV device or connect to the DVI-D output of a PC. (Using a DVI-HDMI cable) 14. VIDEO IN (DVI-D) Connects to the DVI-D output of a PC or connect to the HDMI output of an AV device (Using a DVI-HDMI cable). 15. VGA IN Connects to the VGA output ...

17 2.4. REMOTE CONTROL 2.4.1. GENERAL FUNCTIONS POWER button Press to switch on the display from standby mode. Press again to turn it off to standby mode. This button also acts as the OPS power button when OPS is installed. If OPS is the default video source, OPS will turn on and off at the same time as the display. Note: if OPS is not the default video source, its power status will not be changed when display is turned off. SMART button To select smart picture mode from:  Standard: for images (factory setting)  Highbright: for moving images such as Video  sRGB: for text based images Cinema: for movies PC mode: Standard, High ...

18 BRIGHTNESS button Press to open the Brightness OSD selection, and then press the PLUS or MINUS button to adjust the value. DISPLAY button To turn on/off the information OSD displayed on the upper right corner of the screen. MENU button To turn the OSD menu on/off. UP button  To move the highlight bar up to adjust the selected item when OSD menu is on.  To move the sub-picture up in “PIP” mode. DOWN button  To move the highlight bar down to adjust the selected item when OSD menu is on.  To move the sub-picture down in “PIP” mode. PLUS button  To move the highlight bar right to the 1st or 2nd submenu when OSD menu is ...

19 2.4.2. INSERTING THE BATTERIES IN THE REMOTE CONTROL The remote control is powered by 1.5V AAA batteries. To install or replace batteries: 1. Press and slide to open the cover. 2. Insert two AAA size 1.5V batteries ensuring that the “+” and “-” ends of the batteries are correctly aligned. 3. Replace the cover. Caution: Incorrect use of batteries can result in leaks or bursting. Be careful especially about the following points.  Place “AAA” batteries matching the + and - signs on each battery to the + and - signs of the battery compartment.  Do not mix battery types.  Do not combine new batteries with used ones. I ...